Flowserve Supplement 2 ACCESS I Instrukcja Użytkownika Pobierz pdf

Worcester Controls

HARDWARE AND SOFTWARE

USED IN THIS EXAMPLE

WORCESTER CONTROLS/McCANNA:

• ACCESS 39 Actuator with Integral DeviceNet Interface Module

• Computer Disk of Electronic Data Sheet (.eds) – Supplied with

ACCESS Actuator

ALLEN BRADLEY:

• SLC-503 – Processor

• Four-Slot Rack

• P2 Power Supply

• DeviceNet Scanner Module – (located in slot 4)

• KF2-RS-232 Communication Interface Module

• PC TO Processor Cable 1747-CP3

• RS LOGIC Software

• RS LINX Software

• RS Networx for DeviceNet Software

OTHER:

• Regulated – 24 VDC Power Supply

• DeviceNet System of Cables and Connectors

• 120-ohm Network Terminating Resistors

TEST PROCEDURE

1. Installing Electronic Data Sheet (.eds) File:

Install the .eds file (disk supplied with actuator) from the disk to

the Rockwell .eds folder found on the hard drive as follows:

Rockwell Software \ rs common \ eds

With the .eds file placed as above the RS Networx program will

automatically load the ACCESS .eds file parameters when a network

browse is performed. The .eds file-access actuator (07159) can be

found in the vendor category when running RS Networx.

2. Connect the SLC-Processor to the PC-COM-1 Port and the KF2

module to PC-COM-2 port.

3. On the Actuator DeviceNet Board:

A) Set Switch 1 and 2 to the desired address, i.e., for Address 1

set Switch 1 to 1 and Switch 2 to 0. It is important that the

address is set correctly prior to turning 24 VDC power on to

the network. If the address is changed while power is applied

LED 2 will flash to indicate a communication problem.

B) Set Switch 3 to the desired communication Baud Rate, i.e.,

Position O =125K Baud Rate.

4. With the equipment installed and connected and with power

turned on to the SLC and 24 VDC turned on to the DeviceNet

Network, LEDs D1 and D2 should be steady green.

A flashing LED-D2 indicates that the slave address connected to

the network does not agree with what the scanner had previously

mapped. See step 13.

5. Using RS-LINX - Configure Drivers:

PC-COM-1 Port– to SLC- DF1-1-DH485 – To be running

PC- COM-2 Port– to KFD-1 – To be running

6. Using RS-Networx, configure Network that should consist of

scanner at node – 00; actuator 07159(1) at node-01; KFD module

at node-62.

7. Go online with the Network and upload the slave parameters to

the scanner module.

8. Double click the scanner module and select “module” and upload

scanner parameters.

9. At the scanner module screen select “module” and set the slot

number to the value that the scanner module resides in, i.e., the

scanner was installed in slot 4 in this example.

10. At the scanner module screen select “scanlist” and highlight

01,07159(1)-(which is the access actuator module) in the left

window and using the right arrow move the device into the

right window.

WCAIM2021

(Part 13952)

Supplement 2

ACCESS I and M DeviceNet PLC Example

Installation, Operation and Maintenance Instructions

MAPPING AND OPERATION EXAMPLE USING AN ALLEN BRADLEY SLC-PROGRAMMABLE LOGIC CONTROLLER

ASSUMPTION: WORKING KNOWLEDGE OF ALLEN BRADLEY SLC PROCESSOR AND SOFTWARE

1 2

Supplement 2 1
Worcester Controls 2

Podsumowanie treści

Strona 1 - Supplement 2

Worcester ControlsHARDWARE AND SOFTWARE USED IN THIS EXAMPLEWORCESTER CONTROLS/McCANNA:• ACCESS 39 Actuator with Integral DeviceNet Interface Module•

Strona 2 - Worcester Controls

Flow Control DivisionWorcester ControlsFlowserve Corporation has established industry leadership in the design and manufacture of its products. When p

Komentarze do niniejszej Instrukcji

Brak uwag

Flowserve Supplement 2 ACCESS I Instrukcja Użytkownika

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Sprzęt komputerowy Flowserve Supplement 2 ACCESS I. Flowserve Supplement 2 ACCESS I User Manual Instrukcja obsługi

Podsumowanie treści

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Sprzęt komputerowy Flowserve Supplement 2 ACCESS I