
76
5.5 DS/DM UltraSwitch™ switch options
6. Installation
A variety of mounting hardware is available for
mounting the DS/DM Ultraswitch™ to valve actuators.
For best results, specify the NAMUR shaft option and
NAMUR mounting hardware when installing to NAMUR
compliant actuator.
The NAMUR mounting hardware allow direct
coupling to actuators without adaptors, reducing dead
band. Simply bolt bracket to actuator and DS/DM
UltraSwitch™ to bracket, leaving bolts finger tight.
For NAMUR applications the DS/DM UltraSwitch™
shaft features an integral alignment pin. This pin must
engage the tapped hole in the actuator shaft.
For non-NAMUR applications, make sure to properly
install a coupler between DS/DM UltraSwitch™ and
actuator. Once the DS/DM UltraSwitch™ is installed
with fasteners loosely tightened, stroke the actuator
two or three times to align the bracket. Then tighten
all fasteners.
NOTE: External mounting fasteners must not be
allowed to bottom. Select length of screws to allow
at least one thread turn of clearance against bottom
of female thread when screw is tightened (due to
approval conditions). See picture.
NOTE: If the equipment is likely to come into
contact with aggressive substances, then it is the
responsibility of the user to take suitable precautions
that prevent it from being adversely affected, thus
ensuring that the type of protection provided by the
equipment is not compromised.
Code
Switch Option Manufacturer Part Number Load Capacity
F3 IFM IF5250 10-36VDC NC PNP, 150mA, 3-wire NC
F5 IFM IF6001 18-32VDC,NOPNP,150mA@50°C
F6 IFM IF6034 10-36VDC, NO PNP, 150mA, Stainless steel
F7 IFM IN0074 20-250 AC/DC, NO, 350mA/100mA
F8 IFM IN0081 20-250 AC/DC, NO, 350mA/100mA w/LED
F9 IFM IN0097 20-250V AC/DC NO 2-Wire (H=14 only)
FB IFM IF5249 10-36VDC NO PNP, 150mA, 3-wire NO
FC IFM IF5718 10-36VDC NO PNP/NPN, 150mA, plastic
FG IFM IS5070 10-36 VDC NO PNP 3-wire (H=14 only)
M1 SPDT Honeywell V7-1C13D8-201 15.1A (1/2 HP) at 125/250 AC;
Mechanical MicroSwitch A at 125 VDC; 1/4A at 250VDC; 5A at 120Vac
MG SPDT Honeywell V7-1D19D8-201 1A at 125 VAC / 50 mA at 24 VDC
Gold Mechanical MicroSwitch
N1 Pepperl+Fuchs NJ4-12GM40-E Proximity 3-wire NPN NO 10-60 VDC
N3 Pepperl+Fuchs SJ3,5-S1N NAMUR NO 8V
N8 Solid State Proximity Pepperl+Fuchs NJ2-V3-N NAMUR Sensor Output / 5-25 VDC Supply
N9 Solid State Proximity Pepperl+Fuchs NBB3-V3-Z4 NPN Sourcing/ 100 mA max. Current / 5-60 VDC
NA Pepperl+Fuchs NBN4-12GM40-E2 Inductive. 3 wires PNP NO 10-30VDC
ND Pepperl+Fuchs NCB2-12GM40-Z1 Proximity inductive 2-wire DC NC
NE Pepperl+Fuchs NCB2-12GM35-N0 NAMUR with LED NC 8,2V
NF Pepperl+Fuchs NCN4-12GM35-N0 NAMUR with LED NC 8,2V
NG Pepperl+Fuchs NJ5-11-N-G NAMUR NC 8,2V
NK Pepperl+Fuchs NCN4-12GM40-Z0 Proximity 2-wire DC NO 8,2V
NM Pepperl+Fuchs NJ2-11-SN-G NAMUR NC 5-25 VDC
NP Solid State Proximity Pepperl+Fuchs SJ3.5-N NAMUR 5-25 VDC Supply
NQ Solid State Proximity Pepperl+Fuchs NJ4-12GK-N NAMUR NC-Sensor, 8VDC
NR Solid State Proximity Pepperl+Fuchs NJ4-12GM40-E1 NPN Sinking / 200 mA max. Current / 10-60 VDC
NS Solid State Proximity Pepperl+Fuchs NJ4-12GM40-E2 PNP Sourcing / 200 mA max. Current / 10-60 VDC
NT Solid State Proximity Pepperl+Fuchs NJ4-12GK40-E2 NPN Sourcing / 200 mA max. Current / 10-60 VDC
NW Solid State Proximity Pepperl+Fuchs SJ3,5-SN NAMUR Sensor Output / 5-25 VDC Supply
P4 SPST Proximity Aleph PS-6132 0.35A at 140 VAC / .25A at 200VDC (50 W Max.)
P5 SPDT Proximity Hamlin 59135-030 0.25A at 120 VAC / 0.25A at 28 VDC (3 W Max.)
PE SPDT Sabre Proximity Flowserve XA0199 1A at 120 VAC / 2A at 24 VDC
PP SPDT Phazer Proximity Flowserve XA0155 3A at 120 VAC / 2A at 24 VDC
PT SPST BRS Proximity Flowserve XA0157 3A at 120 VAC / 0.5 at 24 VDC
FCD PMENIM0020-00 - 02/15 FCD PMENIM0020-00 - 02/15
Komentarze do niniejszej Instrukcji