Flowserve Aviator II Valve Controller Instrukcja Użytkownika Pobierz pdf

Installation

Operation

Automax Valve Automation Systems

Aviator II Valve Controller

FCD AXENIOM0100-02

Maintenance

Mechanical Installation: Installation is best performed with the NAMUR mounting kits. These kits allow direct

mounting of the Aviator™II shaft to the actuator pinion without a coupler. The NAMUR mounting kits will work with any

actuator conforming to the NAMUR standard for accessory mounting hole locations and pinion dimensions. Simply attach

bracket to actuator and Aviator™II to bracket with the included fasteners. The Aviator™II shaft features an integral

alignment pin which engages the tapped pinion hole. Automax also offers a full line of non-NAMUR kits.

Electrical Connections: The Aviator™II features three (3) 3/4" NPT conduit entries. The switches and pilot solenoid

are pre-wired to the screw terminal block to simplify customer wiring connections. A wiring diagram is included under the lid.

Simply make desired connections to the screw terminal blocks. Secure a grounding wire under the green grounding screw.

Make sure the solenoid control voltage is the same as the solenoid electrical rating. For hazardous locations, U.L. and

National Electric codes require an approved sealing fitting within 18 inches of the switch enclosure. Sealing fittings are not

required for Division 2 non-incendive applications. Open conduit entries must be closed after installation using a close-up

plug approved for hazardous locations. Conduit and plugs must engage a full five (5) threads.

For field wiring: ensure that any excess wire lengths or loops are routed away from any moving parts and are short

enough, or secured to ensure a ¼” clearance between the wire and the inside surface of the switchbox cover.

Spool and Tubing Configuration: For spring return actuators, a 4-way spool valve is provided with port #2

plugged. For double acting actuators, the same spool valve is provided with no plugs. Make sure the correct spool is

selected before installing tubing. (Note: the APS2 module can be supplied on spring return actuators to purge the spring

chamber with supply air.) 2. Make sure all air pressure is removed before installing tubing. 3. Attach tubing according to

Figures 1 or 2 below, depending upon application. Attach supply tubing to Port 1 and use 3 and 5 exhaust. 4. To prolong

actuator life use only clean, dry plant air. Lubricated air is not required, although it is recommended particularly for high

cycle applications.

NOTE: A minimum of 35 psi is required to operate the spool valve.

Figure 1 Figure 2

Double Acting Actuator Spring Return Actuator

Caution: To prevent ignition of hazardous atmospheres, keep cover bolts tight while circuits are live. Disconnect supply

circuit before opening removing the lid. Do not place the lid with the flat surfaces down. This will ensure that the flange is not

damaged and integrity of the flame path will be maintained.

1 2 3 4 5 6 7 8

Podsumowanie treści

Strona 1 - Maintenance

InstallationOperation Automax Valve Automation Systems Aviator II Valve Controller FCD AXENIOM0100-02 Main

Strona 2 - KEMA 07ATEX0122X

Certifications: The Aviator II has globally accepted certifications. 0518 IECEx CSA 07.0009X Flameproof Ex d IIB T3/T4 T3

Strona 3

Switch Setting 1. Rotate actuator to desired position. 2. Loosen five captive cover screws and remove lid, turning slightly while lifting.

Strona 4 - AVIATOR II SWITCH OPTIONS

AVIATOR II SWITCH OPTIONS AVIATOR II WITH MECHANICAL SWITCHES

Strona 5

AVIATOR II WITH AS-i/DeviceNET CARD AVIATOR II WITH FF NETWORK CARD

Strona 6

SOLENOID OPTIONS

Strona 7 - SPOOL VALVE OPTIONS

SPOOL VALVE OPTIONS 1.8 Cv Spool Option 4.5 Cv Spool Option

Strona 8

Flowserve Corporation 1350 Mountain Springs Parkway Springville, Utah, Utah, 84663 801 489-8611 Flowserve Corporation 1978 Foreman Drive Cook

Komentarze do niniejszej Instrukcji

Brak uwag

Flowserve Aviator II Valve Controller Instrukcja Użytkownika

Przeglądaj online lub pobierz Instrukcja Użytkownika dla Sprzęt komputerowy Flowserve Aviator II Valve Controller. Flowserve Aviator II Valve Controller User Manual Instrukcja obsługi

Podsumowanie treści

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Sprzęt komputerowy Flowserve Aviator II Valve Controller