Flowserve LNGT Instrukcja Użytkownika Pobierz pdf (Strona 29)

LNGT USER INSTRUCTIONS ENGLISH 00083107 02-08

Page 29 of 48

Before restarting the machine, the relevant

instructions listed in section 5, Commissioning,

start up, operation and shut down must be

observed.

Oil and grease leaks may make the ground

slippery. Machine maintenance must always

begin and finish by cleaning the ground and the

exterior of the machine.

If platforms, stairs and guard rails are required for

maintenance, they must be placed for easy access

to areas where maintenance and inspection are to

be carried out. The positioning of these

accessories must not limit access or hinder the

lifting of the part to be serviced.

When air or compressed inert gas is used in the

maintenance process, the operator and anyone in

the vicinity must be careful and have the

appropriate protection.

Do not spray air or compressed inert gas on skin.

Do not direct an air or gas jet towards other people.

Never use air or compressed inert gas to clean

clothes.

Before working on the pump, take measures to

prevent an uncontrolled start. Put a warning board

on the starting device with the words:

"Machine under repair: do not start".

With electric drive equipment, lock the main switch

open and withdraw any fuses. Put a warning board

on the fuse box or main switch with the words:

"Machine under repair: do not connect".

Never clean equipment with inflammable solvents

or carbon tetrachloride. Protect yourself against

toxic fumes when using cleaning agents.

6.2 Maintenance schedule

It is recommended that a maintenance plan

and schedule is adopted, in line with these User

Instructions. It should include the following:

a) Any auxiliary systems installed must be

monitored, if necessary, to ensure they function

correctly.

b) Gland packings must be adjusted correctly to

give visible leakage and concentric alignment

of the gland follower to prevent excessive

temperature of the packing or follower.

c) Check for any leaks from gaskets and seals.

The correct functioning of the shaft seal must

be checked regularly.

d) Check bearing lubricant level, and if the hours

run show a lubricant change is required.

e) Check that the duty condition is in the safe

operating range for the pump.

f) Check vibration, noise level and surface

temperature at the bearings to confirm

satisfactory operation.

g) Check dirt and dust is removed from areas

around close clearances, bearing housings and

motors.

h) Check coupling alignment and re-align if

necessary.

Our specialist service personnel can help with

preventative maintenance records and provide

condition monitoring for temperature and vibration

to identify the onset of potential problems.

If any problems are found the following sequence

of actions should take place:

a) Refer to section 7, Faults; causes and

remedies, for fault diagnosis.

b) Ensure equipment complies with the

recommendations in this manual.

c) Contact Flowserve if the problem persists.

6.2.1 Routine inspection [daily/weekly]

The following checks should be

made and the appropriate action taken to remedy

any deviations:

a) Check operating behavior. Ensure noise,

vibration and bearing temperatures are normal.

b) Check that there are no abnormal fluid or

lubricant leaks [static and dynamic seals] and

that any sealant systems [if fitted] are full and

operating normally.

c) Check that shaft seal leaks are within

acceptable limits.

d) Check the level and condition of oil lubricant.

On grease lubricated pumps, check running

hours since last recharge of grease or

complete grease change.

e) Check any auxiliary supplies eg

heating/cooling, if fitted, are functioning

correctly.

 Refer to the manuals of any associated

equipment for routine checks needed.

1 2 ... 24 25 26 27 28 29 30 31 32 33 34 ... 47 48

Komentarze do niniejszej Instrukcji

Brak uwag

Modelos	Tipo de documento
Criterion	Lista de partes GE Criterion Renewal Parts, 2 paginas
GFDN245	Manual de usuario GE GFDN245 User's Manual, 60 paginas
NEMA Premium Efficient XsD Ultra	Manual de instalación GE NEMA Premium Efficient XsD Ultra Installation and Maintenance Manual, 20 paginas
ECBA	Guía de instalación GE ECBA Installation Guide, 6 paginas
M-400R2	Ficha de datos GE M-400R2 Data Sheet, 4 paginas
gea31409	Folleto GE gea31409 Brochure, 12 paginas
PP980	Manual de usuario GE PP980 User's Manual, 40 paginas
USLT Series	Folleto GE USLT Series Brochure, 1 paginas
RM94905	Manual de usuario GE RM94905 User's Manual, 28 paginas
AL10	Manual de usuario GE AL10 Design Files, 4 paginas
SMARTWATER GXSF27B	Manual de usuario GE SMARTWATER GXSF27B User's Manual, 3 paginas
Silent Alert 45137	Manual de usuario GE Silent Alert 45137 User's Manual, 12 paginas
JP626WFWW	Manual de usuario GE JP626WFWW User's Manual, 28 paginas
ECBA	Ficha de datos GE ECBA Data Sheet, 4 paginas
Valve Regulators Mooney Specialty	Folleto GE Valve Regulators Mooney Specialty Brochure, 20 paginas
OG5	Ficha de datos GE OG5 Data Sheet, 4 paginas
WMTS	Guía de instalación GE WMTS Installation Guide, 4 paginas
BL Series	Guía de instalación GE BL Series Installation Guide, 6 paginas
EDV	Guía de instalación GE EDV Installation Guide, 2 paginas
ERX1	Guía de instalación GE ERX1 Installation Guide, 12 paginas

Flowserve LNGT Instrukcja Użytkownika Strona 29

Komentarze do niniejszej Instrukcji

GE Monogram ZEU769BC manuales

Ge Monogram ZEU769BC Manual de usuario (2 paginas)

Tabla de contenidos

Más productos y manuales para No GE

Flowserve LNGT Instrukcja Użytkownika Strona 29

Komentarze do niniejszej Instrukcji

Powiązane produkty i podręczniki dla Pompy Flowserve LNGT

GE Monogram ZEU769BC manuales

Ge Monogram ZEU769BC Manual de usuario (2 paginas)

Tabla de contenidos

Más productos y manuales para No GE